Battery or hardwired shades: how to choose, and what to plan before drywall
If your walls are closed, battery shades are usually the answer. If they are open, you have a short window to make wired shades easy. This guide covers both.
Book a free in-home consultationBattery shades
- No wiring: installed in a finished room.
- They run on alkaline batteries (D cells in roller shades; some honeycomb shades use AA). Lutron's own pages give battery life from about two to five years, depending on the shade's size, its fabric and how often it moves; large shades used often need them sooner.
- Lutron lists its battery roller shades up to 108 inches wide, or 144 inches in the wide version.
- A shade is ordered as battery or wired and is not converted later.
Plug-in shades
A middle path for one or two hard-to-reach shades: a small adapter plugs into an outlet near the top of the window. No wiring is done, but the cord shows unless an electrician adds an outlet where it can be hidden.
Hardwired shades
- Low-voltage power runs to each window from a central panel or supply.
- Nothing to change over the years.
- Suited to wide and tall glass, drapery tracks and shades hidden in ceiling pockets. Lutron lists its wired roller shades up to 18 to 20 feet wide and its drapery tracks up to 41 feet.
- Even the wireless version of Lutron's Sivoia shades needs power wiring; only the control signal is wireless.
- Wired Triathlon shades run on 12 volts and Lutron's Sivoia and Palladiom shades on 35 volts, so they do not share a power panel. Choose the line before the panel is planned.
- They need solid blocking, and a pocket or fascia wherever the roll should be hidden.
The before-drywall checklist
- Decide which windows get shades, now or later. Pre-wire the later ones too.
- Choose the power for each: battery (nothing to do), plug-in (an outlet at the window head) or low-voltage wired (cable to a panel).
- Low-voltage runs: one home run from each wired window to the power panel location. Use the cable the shade maker specifies; do not substitute.
- Power panel: a dry, reachable spot such as a closet or the equipment room, with wall space and a dedicated outlet or circuit installed by the electrician.
- Pockets or fascia: if the roll should disappear, frame the pocket and confirm its inside dimensions with us before framing closes.
- Blocking: solid wood blocking across the head of every shaded window, wider than the window for outside mounts and drapery tracks.
- Clearances: handles, cranks, alarm contacts and trim that sit in the shade's path.
- Controls: keypad locations at room entries, low-voltage or line-voltage as the system requires.
- Network: a network cable to where the hub or processor will sit.
- Label and photograph every run before insulation, and send us the photos.
- Who does what: the builder frames pockets and blocking; the electrician does all line-voltage work; the low-voltage or shade contractor pulls shade cable, as licenses allow; Sun Blinds measures, supplies and installs the shades.
General planning guidance. The shade maker's installation instructions and local code govern.
If the lights are part of the plan
Lighting control is planned at the same time. Dimmers and keypads sit in wall boxes, which is line-voltage work for a licensed electrician, and some dimmer models need a neutral wire in the box. A whole-home system also needs its processor on your home network, so plan a network cable to where it will sit.
Who to call, and when
Talk to us at framing or the electrical walk-through, not at move-in. That is when power, pockets and blocking cost the least to add.
Thinking about the budget? See what decides the cost of motorized shades, or go back to Lutron shades and lighting.
Questions
Can I pre-wire now and buy shades later?
Yes. Running low-voltage cable to each window and adding blocking while the walls are open keeps wired shades possible later, even if you start with none.
Can battery shades be converted to wired?
No. A shade is ordered as battery or wired and is not converted later, so choose per window before ordering.
What if I already have Lutron lighting?
Tell us the system and, if you know them, the processor and device models. Shades can often join the system you have; different generations have different requirements.
Do wired shades work in a power cut?
Battery shades keep working. Lutron remotes and keypads talk over Lutron's own radio rather than Wi-Fi, so they keep working when the internet is down. For wired shades in a power cut, ask us about the model you are considering, because it depends on the system and its power supply.
Planning a build or a remodel?
Book a free in-home consultation. We look at each window, bring samples and give you a written proposal.
Book a free in-home consultationOr call us: (916) 538-9934 (Sacramento region) or (510) 556-4233 (Bay Area)